SlittingHZ-FT-1600*2-SS-003
Precision double-slitter line
Turns master coils into precisely sized strips. Two slitter heads let one set of knives run while the next is set up.
- Material thickness
- 0.3–2.5 mm
- Coil weight
- ≤ 15 t
Equipment
11 line types for slitting, cut-to-length and combined processing. Every line is built to your coil width, thickness range and output, and run in our factory before it ships.
- 11 types
- Line types
- 0.2–16mm
- Material thickness
- up to 25t
- Coil weight
- 300–1650mm
- Coil width
- 500–6000mm
- Sheet length
Slitting1400 series
High-precision light-gauge slitting line
For thin stainless, cold-rolled and galvanized coil where strip width tolerance and clean edges matter. AC drive and a Taiwan-derived slitter design.
- Material thickness
- 0.3–2.0 mm
Slitting1400 series
Galvanized coil slitting line
Slits galvanized and coated coil into strips, with a belt tension unit ahead of the recoiler to protect the surface.
- Material thickness
- 0.3–2.0 mm
- Coil width
- 1400 mm
Slitting1600 series
Heavy-duty slitting line
A heavier frame and larger arbors for wide coil up to 15 t, running stainless, hot-rolled, cold-rolled and galvanized steel.
- Coil width
- 1600 mm
- Coil weight
- ≤ 15 t
SlittingThick plate series
Thick plate slitting line
Slits plate coil from 3 to 16 mm, with a rigid knife stand and heavy pinch and straightening rolls ahead of it.
- Material thickness
- 3–16 mm
SlittingHZ-850
HZ-850 single-slitter line
A compact line for aluminum, copper and steel coil. Can be combined with a cut-to-length section.
- Series
- 850
Cut-to-lengthHZP-1600*3-SS-010
Rotary cut-to-length line
Levels coil and cuts it into sheets with a rotary shear, then stacks them. Built around the 1600 series.
- Series
- 1600
- Sheet length
- 500–4000 mm
Cut-to-length1600 series
Flying shear cut-to-length line
Cuts sheets on the move, so the strip keeps running between cuts. For middle-gauge coil and long sheets.
- Coil width
- 300–1600 mm
- Coil weight
- 8–25 t
Cut-to-length1400 series
Automatic leveling and cross-cutting machine
A compact leveler and cross-cutting shear for thin coil, with a roller table that carries the sheets out.
- Material thickness
- 0.2–2.0 mm
- Coil width
- 1400 mm
Cut-to-length1650 series
Heavy-gauge leveling cut-to-length line
Levels thicker coil with a precision leveler and cuts it into flat plates.
- Coil width
- 1650 mm
Combination
Slitting and cut-to-length combination line
Levels, slits and cuts to length on one line, for plants that need both strip and sheet from the same coil.
- Processes
- Leveling, slitting, cut-to-length
What runs through your plant?
The material decides the knives, the tension system and the surface protection. These are the details we ask for first.
| Material | Tell us |
|---|---|
| Stainless steel | Grade, surface finish, protective film |
| Carbon and cold-rolled steel | Thickness range, yield strength, output per shift |
| Galvanized and coated steel | Coating type, surface protection, strip edge quality |
| Aluminum and copper | Alloy, temper, burr tolerance |
Send us your coil. We will send you a line.
Material, thickness, coil width and weight, and the strip or sheet you need. That is enough to start.